Design a single trace or a differential pair and calculate its impedance.
Differential pair impedance
A differential pair is two traces driven in opposite polarity. USB pairs are commonly 90 Ω, Ethernet, HDMI, LVDS and many PCIe routes are commonly 100 Ω, and PCIe also uses 85 Ω. The widths below come from this site’s quick coupled-line model.
90 Ω, 100 Ω and 85 Ω
USB high-speed pairs are commonly routed at 90 Ω differential so the board meets the 90 Ω cable. Ethernet 100BASE-TX and 1000BASE-T, HDMI TMDS and LVDS are commonly 100 Ω. PCIe board designs are commonly 85 Ω or 100 Ω, depending on the generation and the device. The interface specification and the silicon note decide the target. This page only shows what the model does at 85 Ω, 90 Ω and 100 Ω.
Differential impedance is not the impedance of one trace with the other one removed. The calculator also reports that isolated Z0. The two numbers meet only when the traces are far apart.
Edge-coupled geometry
An edge-coupled pair is two traces side by side. S is the copper-to-copper edge gap, not the center-to-center pitch. On a microstrip both traces sit on the outer layer over one plane, and the coupling factor uses S/H. On a symmetric stripline both traces are centered between two planes. The plane spacing is B = 2H + T, and the coupling factor uses S/B. H is the clearance from each trace to one plane.
The published JLCPCB and PCBWay four-layer and six-layer drawings do not put an inner pair in that centered geometry. An inner trace usually sits closer to one plane than the other, often with a different material on each side. That offset pair has no closed form here. The centered row later on this page is the symmetric formula with H = 0.200 mm, T = 0.035 mm and εr = 4.2. It is not one of those fabricator drawings. Use the 2D solver for an offset pair.
Odd mode, even mode and the quick factor
Odd mode drives the two traces in opposite polarity. That is the differential signal, and Zdiff = 2 Zodd. Even mode drives them in the same polarity. That is the common signal, and Zcommon = Zeven / 2. A length mismatch converts part of the differential signal into common mode at the receiver. The cross-section still sets the impedances.
The quick model does not solve Zeven. It takes the isolated Hammerstad–Jensen or IPC-2141 impedance and multiplies by a coupling factor from the TI LVDS note. Microstrip uses 0.48 exp(−0.96 S/H). Stripline uses 0.347 exp(−2.9 S/B). As S grows, the factor goes to zero and Zdiff goes to twice the isolated impedance. The factor does not depend on W. The advanced network panel reports complex Zodd and Zeven from the RLGC matrices. That is a different model.
Because the factor ignores width, a tightly coupled pair needs a narrower trace to hold the same Zdiff: the isolated impedance has to be higher so that, after coupling, the differential target is met. A loosely coupled pair sits close to Zdiff/2 on each trace. Dividing the target by two is only the far-apart limit.
Coupling versus spacing
This sweep holds the trace at the 50 Ω single-ended width for the illustrative 0.200 mm, εr 4.2, 1 oz microstrip, W = 0.3512 mm, and changes only the edge gap. At S = 0.15 mm the differential impedance is 76.64 Ω and the coupling factor is 0.234. It is not 100 Ω. At a 1 mm gap the same trace is back near 100 Ω, which is two times 50 Ω.
The stripline sweep uses the same idea on the centered construction: the width is the single-ended 50 Ω width, and only S changes. Coupling falls faster with S/B than the microstrip factor falls with S/H, which is what the two exponents say.
| S (mm) | Zdiff (Ω) | Coupling factor |
|---|---|---|
| 0.100 | 70.30 | 0.297 |
| 0.150 | 76.64 | 0.234 |
| 0.200 | 81.62 | 0.184 |
| 0.300 | 88.63 | 0.114 |
| 0.500 | 95.65 | 0.044 |
| 1.000 | 99.60 | 0.004 |
| S (mm) | Zdiff (Ω) | Coupling factor |
|---|---|---|
| 0.100 | 82.18 | 0.178 |
| 0.150 | 87.23 | 0.128 |
| 0.200 | 90.85 | 0.091 |
| 0.300 | 95.30 | 0.047 |
| 0.500 | 98.76 | 0.012 |
| 1.000 | 99.96 | 0.000 |
Length matching
In this uniform-line model, length does not set impedance. W, S, H, T and εr do. Length sets delay. Match the two members of a pair to each other so those delays agree. A skew budget, in picoseconds or in millimetres, belongs to the interface specification, not to the impedance formula.
Keep the extra length on the same layer, and at the same spacing as the rest of the pair when the layout allows it. A serpentine that opens the gap changes the local impedance as well as the delay. Matching one pair to a different pair is a separate, usually looser, constraint. Do not add length to pull a pair onto 100 Ω.
Width and spacing on common stackups
The microstrip rows solve the width at a fixed edge gap of 0.15 mm, unless the row says 0.10 mm. Targets are 85 Ω, 90 Ω and 100 Ω. Isolated Z0 is the impedance of one trace at that width with the other trace removed. It is not Zdiff/2. The coupling factor is 1 − Zdiff / (2 Z0) from the quick model.
On the 0.200 mm, εr 4.2 microstrip, 85 Ω needs W = 0.2875 mm, 90 Ω needs W = 0.2555 mm and 100 Ω needs W = 0.2021 mm, all at S = 0.15 mm. Tightening that 100 Ω pair to S = 0.10 mm moves the width to 0.1634 mm. The centered stripline at the same 0.15 mm gap needs W = 0.1021 mm for 100 Ω. Thin prepregs flagged T/H > 0.2 are outside the microstrip thickness correction. JLCPCB’s impedance page lists a minimum trace and space of 3.5 mil, which is 0.089 mm. Compare a solved width with the fabricator’s current minimum before you use it.
| Construction | Target (Ω) | H (mm) | εr | S (mm) | W (mm) | W (mil) | Isolated Z0 (Ω) | Coupling factor | Range | Calculate |
|---|---|---|---|---|---|---|---|---|---|---|
| Illustrative prepreg, 0.200 mm, εr 4.2 | 85 | 0.200 | 4.2 | 0.150 | 0.2875 | 11.32 | 55.46 | 0.234 | — | Calculate Illustrative prepreg, 0.200 mm, εr 4.2, 85 Ω |
| Illustrative prepreg, 0.200 mm, εr 4.2 | 90 | 0.200 | 4.2 | 0.150 | 0.2555 | 10.06 | 58.72 | 0.234 | — | Calculate Illustrative prepreg, 0.200 mm, εr 4.2, 90 Ω |
| Illustrative prepreg, 0.200 mm, εr 4.2 | 100 | 0.200 | 4.2 | 0.150 | 0.2021 | 7.96 | 65.24 | 0.234 | — | Calculate Illustrative prepreg, 0.200 mm, εr 4.2, 100 Ω |
| Illustrative prepreg, 0.200 mm, εr 4.5 | 85 | 0.200 | 4.5 | 0.150 | 0.2701 | 10.63 | 55.46 | 0.234 | — | Calculate Illustrative prepreg, 0.200 mm, εr 4.5, 85 Ω |
| Illustrative prepreg, 0.200 mm, εr 4.5 | 90 | 0.200 | 4.5 | 0.150 | 0.2393 | 9.42 | 58.72 | 0.234 | — | Calculate Illustrative prepreg, 0.200 mm, εr 4.5, 90 Ω |
| Illustrative prepreg, 0.200 mm, εr 4.5 | 100 | 0.200 | 4.5 | 0.150 | 0.188 | 7.40 | 65.24 | 0.234 | — | Calculate Illustrative prepreg, 0.200 mm, εr 4.5, 100 Ω |
| JLCPCB JLC04161H-7628 drawing | 85 | 0.2104 | 4.4 | 0.150 | 0.2852 | 11.23 | 56.08 | 0.242 | — | Calculate JLCPCB JLC04161H-7628 drawing, 85 Ω |
| JLCPCB JLC04161H-7628 drawing | 90 | 0.2104 | 4.4 | 0.150 | 0.2529 | 9.96 | 59.38 | 0.242 | — | Calculate JLCPCB JLC04161H-7628 drawing, 90 Ω |
| JLCPCB JLC04161H-7628 drawing | 100 | 0.2104 | 4.4 | 0.150 | 0.199 | 7.83 | 65.97 | 0.242 | — | Calculate JLCPCB JLC04161H-7628 drawing, 100 Ω |
| JLCPCB JLC04161H-3313 | 85 | 0.0994 | 4.1 | 0.150 | 0.1773 | 6.98 | 47.90 | 0.113 | T/H > 0.2 | Calculate JLCPCB JLC04161H-3313, 85 Ω |
| JLCPCB JLC04161H-3313 | 90 | 0.0994 | 4.1 | 0.150 | 0.1582 | 6.23 | 50.72 | 0.113 | T/H > 0.2 | Calculate JLCPCB JLC04161H-3313, 90 Ω |
| JLCPCB JLC04161H-3313 | 100 | 0.0994 | 4.1 | 0.150 | 0.1262 | 4.97 | 56.35 | 0.113 | T/H > 0.2 | Calculate JLCPCB JLC04161H-3313, 100 Ω |
| PCBWay 4-layer 1.6 mm, 1 oz, 70% | 85 | 0.1855 | 4.74 | 0.150 | 0.2446 | 9.63 | 54.55 | 0.221 | — | Calculate PCBWay 4-layer 1.6 mm, 1 oz, 70%, 85 Ω |
| PCBWay 4-layer 1.6 mm, 1 oz, 70% | 90 | 0.1855 | 4.74 | 0.150 | 0.2164 | 8.52 | 57.76 | 0.221 | — | Calculate PCBWay 4-layer 1.6 mm, 1 oz, 70%, 90 Ω |
| PCBWay 4-layer 1.6 mm, 1 oz, 70% | 100 | 0.1855 | 4.74 | 0.150 | 0.1693 | 6.66 | 64.17 | 0.221 | — | Calculate PCBWay 4-layer 1.6 mm, 1 oz, 70%, 100 Ω |
| PCBWay 6-layer 1.6 mm, 1 oz, 70% | 85 | 0.1195 | 4.45 | 0.150 | 0.190 | 7.48 | 49.64 | 0.144 | T/H > 0.2 | Calculate PCBWay 6-layer 1.6 mm, 1 oz, 70%, 85 Ω |
| PCBWay 6-layer 1.6 mm, 1 oz, 70% | 90 | 0.1195 | 4.45 | 0.150 | 0.169 | 6.65 | 52.56 | 0.144 | T/H > 0.2 | Calculate PCBWay 6-layer 1.6 mm, 1 oz, 70%, 90 Ω |
| PCBWay 6-layer 1.6 mm, 1 oz, 70% | 100 | 0.1195 | 4.45 | 0.150 | 0.1337 | 5.26 | 58.40 | 0.144 | T/H > 0.2 | Calculate PCBWay 6-layer 1.6 mm, 1 oz, 70%, 100 Ω |
| Illustrative prepreg 0.200 mm, εr 4.2, S = 0.10 mm | 100 | 0.200 | 4.2 | 0.100 | 0.1634 | 6.43 | 71.13 | 0.297 | — | Calculate Illustrative prepreg 0.200 mm, εr 4.2, S = 0.10 mm, 100 Ω |
| Target (Ω) | S (mm) | W (mm) | W (mil) | Isolated Z0 (Ω) | B (mm) | W/B | Coupling factor | Calculate |
|---|---|---|---|---|---|---|---|---|
| 85 | 0.150 | 0.1519 | 5.98 | 48.72 | 0.435 | 0.349 | 0.128 | Calculate Centered stripline, H = 0.200 mm, 85 Ω |
| 90 | 0.150 | 0.1336 | 5.26 | 51.59 | 0.435 | 0.307 | 0.128 | Calculate Centered stripline, H = 0.200 mm, 90 Ω |
| 100 | 0.150 | 0.1021 | 4.02 | 57.32 | 0.435 | 0.235 | 0.128 | Calculate Centered stripline, H = 0.200 mm, 100 Ω |
Common mistakes
- Using the center-to-center pitch as S. This model wants the copper-to-copper edge gap.
- Setting each trace to 50 Ω and expecting 100 Ω while the traces are close. At S = 0.15 mm on the 0.200 mm example, that trace is 76.64 Ω differential.
- Calling Zdiff/2 the isolated impedance. The table lists both, and they differ by the coupling factor.
- Routing the pair across a split in the reference plane. The formulas assume a continuous plane.
- Using the symmetric stripline formula for an offset inner layer on a four-layer or six-layer drawing.
- Opening the gap inside a length-match serpentine, or adding length in order to change the impedance.
Questions
Is USB 90 Ω and Ethernet 100 Ω?
USB high-speed pairs are commonly routed at 90 Ω differential. Ethernet 100BASE-TX and 1000BASE-T, HDMI TMDS and LVDS are commonly 100 Ω. PCIe is commonly 85 Ω or 100 Ω depending on the generation and the device. The specification you are building to wins over this table.
How does spacing change the width?
Closer spacing raises the coupling, lowers Zdiff for a fixed width, and forces a narrower trace to recover the target. On the 0.200 mm, εr 4.2 microstrip, 100 Ω at S = 0.15 mm needs W = 0.2021 mm, and at S = 0.10 mm it needs W = 0.1634 mm. In this quick model the coupling factor depends on S/H or S/B, not on W.
What are odd mode and even mode?
Odd mode is opposite polarity on the two traces and carries the differential signal. Even mode is the same polarity and carries the common signal. Zdiff = 2 Zodd and Zcommon = Zeven / 2. The quick formula does not solve Zeven. It scales the isolated impedance by the TI coupling factor. The network panel’s Zodd and Zeven come from the RLGC matrices.
Does length matching set the differential impedance?
No. Length sets delay. The cross-section sets impedance. Match the two traces of the pair so their delays agree, and choose W and S for the impedance. The allowed skew is in the interface specification.
Will a fabricator build these exact widths?
Treat the table as a computed starting point from the cited drawings, without solder mask. Thin rows carry the T/H > 0.2 warning. Ask the fabricator to hit the impedance on the stackup they will actually press.
Why is the stripline example not a JLCPCB six-layer pair?
On the published four-layer and six-layer drawings, an inner trace is offset: the dielectric above it and below it differ. The IPC-2141 expression used here needs a trace centered between the planes, with B = 2H + T. The centered row uses H = 0.200 mm to each plane, T = 0.035 mm and εr = 4.2, and 100 Ω comes out at W = 0.1021 mm. It is not a fabricator stackup.
Sources
Independent project, without affiliation or endorsement by the cited authors, publishers or manufacturers. Trademarks belong to their respective owners.
- Qucs Technical Papers, microstrip equations 11.4–11.25
- Analog Devices MT-094, IPC-2141 surface microstrip
- Polar Instruments, Calculation of PCB Track Impedance
- Texas Instruments LVDS Owner’s Manual, edge-coupled factor
- JLCPCB controlled-impedance stackups
- JLCPCB impedance note, 7.1 mil outer height
- PCBWay multilayer laminated structure
PCB impedance guides50 Ω microstrip guideMethod and validation