Design a single trace or a differential pair and calculate its impedance.
50 Ω microstrip trace width
A surface microstrip is an outer-layer PCB trace over one reference plane. Its characteristic impedance is set by width, copper thickness, dielectric height and permittivity. The widths below are the widths this site’s Hammerstad–Jensen solver calls 50 Ω.
What a microstrip is
H is the clearance from the trace copper to the reference plane, not the finished board thickness. W is the trace width and T is the copper thickness. εr is the relative permittivity of the dielectric between that trace and that plane. On a four-layer or six-layer board the outer trace references the nearest inner plane across one prepreg, often near 0.1 mm or 0.2 mm. A width copied from a 1.6 mm two-layer board is then several times too wide.
For the illustrative two-layer rows, a finished thickness of 1.6 mm with 1 oz copper on both sides gives H = 1.530 mm, because 1.6 − 2 × 0.035 = 1.530. That assumes the quoted 1.6 mm already includes both foils. A laminate that quotes 1.6 mm as the core thickness is a different H. One ounce of copper is 0.035 mm in this calculator. Solder mask, etch taper, glass weave and frequency dependence are outside the quick formula.
Hammerstad–Jensen and IPC-2141
The quick result in the calculator is Hammerstad and Jensen’s quasi-static microstrip, with their modification of Wheeler’s thickness correction. It is the same family of expressions as Qucs equations 11.4–11.25. u = W/H. The model is flagged when W/H leaves 0.01 to 100, or when T/H exceeds 0.2. On the Polar Instruments geometry H = 0.794 mm, T = 0.035 mm and εr = 4.2, it reads 88.33 Ω, 50.26 Ω and 29.98 Ω at widths 0.45 mm, 1.5 mm and 3.3 mm. Polar’s numerical column is 89.63 Ω, 50.63 Ω and 30.09 Ω.
IPC-2141, as quoted by Analog Devices MT-094, is a different fit. It is not the number the calculator displays. The usual stated range is about 0.1 ≤ W/H ≤ 2, and MT-094 notes that it is most useful between roughly 50 Ω and 100 Ω. At the Polar width of 0.45 mm the expression returns 91.34 Ω. At 3.3 mm, where W/H is about 4.2 and outside the fit, it returns 21.07 Ω against a field result near 30 Ω.
The table uses Hammerstad–Jensen to choose the width that is 50 Ω, then evaluates IPC-2141 at that same width. Where the IPC expression can still reach 50 Ω with a positive logarithm, its own width is listed too. Delay in the calculator uses the Hammerstad–Jensen effective permittivity, which depends on W/H. It is not the width-independent IPC line 0.475 εr + 0.67.
Height, width, copper and permittivity
The reference trace is the illustrative 0.200 mm dielectric at εr 4.2 and 1 oz. Hammerstad–Jensen puts it at 50 Ω when W = 0.3512 mm. Each row below changes one input and leaves the others at that reference. Ten percent more height raises the impedance to 52.85 Ω, and ten percent less lowers it to 46.94 Ω. Ten percent more width lowers it to 47.46 Ω, and ten percent less raises it to 52.85 Ω.
Half-ounce copper, 0.0175 mm, reads 51.48 Ω at the same width. Two-ounce copper, 0.070 mm, reads 47.79 Ω, and T/H then exceeds 0.2, so the thickness correction is outside the range the calculator warns about. Raising εr from 4.2 to 4.5 at the same width lowers the impedance to 48.48 Ω. The 50 Ω width itself moves from 0.3512 mm at εr 4.2 to 0.3314 mm at εr 4.5. Wider copper, higher permittivity and a shorter dielectric all lower Z0. A wider trace lowers Z0. More height raises it.
| Change | H (mm) | W (mm) | T (mm) | εr | Z0 (Ω) |
|---|---|---|---|---|---|
| Height +10% | 0.220 | 0.3512 | 0.035 | 4.2 | 52.85 |
| Height −10% | 0.180 | 0.3512 | 0.035 | 4.2 | 46.94 |
| Width +10% | 0.200 | 0.3863 | 0.035 | 4.2 | 47.46 |
| Width −10% | 0.200 | 0.3161 | 0.035 | 4.2 | 52.85 |
| Half-ounce copper | 0.200 | 0.3512 | 0.0175 | 4.2 | 51.48 |
| Two-ounce copper | 0.200 | 0.3512 | 0.070 | 4.2 | 47.79 · T/H > 0.2 |
| εr = 4.5 | 0.200 | 0.3512 | 0.035 | 4.5 | 48.48 |
Solder mask
Both quick formulas assume air above the trace. A solder mask adds dielectric in the fringe field and lowers Z0, so a bare width runs a little high once the board is coated. JLCPCB publishes the mask used for its impedance stackups: 1.2 mil above the substrate, 0.6 mil over the trace, 1.2 mil between traces, and a mask permittivity of 3.8.
On the JLC04161H-7628 drawing, at the bare Hammerstad–Jensen width of 0.3572 mm, this site’s electrostatic-2d-v7 solver at mesh h/16 reads 50.98 Ω with no mask and 49.20 Ω with that published mask. The drop is 1.79 Ω on this one geometry. It is not a universal offset, and it is not a substitute for the fabricator’s solver. The quick readout stays blank once a mask is entered, because the closed form does not include it. Open the coated geometry and run the 2D solver to move the width.
Open the JLC04161H-7628 geometry with the published solder mask
50 Ω widths on common stackups
Every Hammerstad–Jensen width in this table is the width the solver returns for a 50 Ω target. The IPC column is the impedance IPC-2141 assigns to that same width, and the following column is the width IPC-2141 itself would call 50 Ω. Rows marked T/H > 0.2 are outside the thickness correction. The solver still returns a number, and the calculator shows the same warning.
These are published nominal dielectrics or, where the row says illustrative, a stated assumption. Pressed thickness, glass style and the permittivity the fabricator actually uses can differ. A controlled-impedance order should name the target and the layer, and let the fabricator adjust the width on the current stackup. The quick model has no mask, so outer-layer widths here are bare-copper estimates.
| Construction | H (mm) | εr | W (mm) | W (mil) | IPC-2141 Z0 (Ω) | IPC-2141 W (mm) | Range | Calculate |
|---|---|---|---|---|---|---|---|---|
| Illustrative 2-layer, 1.6 mm finished, εr 4.2 | 1.530 | 4.2 | 2.9642 | 116.70 | 49.06 | 2.888 | — | Calculate Illustrative 2-layer, 1.6 mm finished, εr 4.2 |
| Illustrative 2-layer, 1.6 mm finished, εr 4.5 | 1.530 | 4.5 | 2.8122 | 110.72 | 49.65 | 2.7846 | — | Calculate Illustrative 2-layer, 1.6 mm finished, εr 4.5 |
| Illustrative prepreg, 0.200 mm, εr 4.2 | 0.200 | 4.2 | 0.3512 | 13.83 | 48.89 | 0.3395 | — | Calculate Illustrative prepreg, 0.200 mm, εr 4.2 |
| Illustrative prepreg, 0.200 mm, εr 4.5 | 0.200 | 4.5 | 0.3314 | 13.05 | 49.48 | 0.326 | — | Calculate Illustrative prepreg, 0.200 mm, εr 4.5 |
| Illustrative prepreg, 0.100 mm, εr 4.2 | 0.100 | 4.2 | 0.1605 | 6.32 | 47.66 | 0.1479 | T/H > 0.2 | Calculate Illustrative prepreg, 0.100 mm, εr 4.2 |
| Illustrative prepreg, 0.100 mm, εr 4.5 | 0.100 | 4.5 | 0.1506 | 5.93 | 48.20 | 0.1411 | T/H > 0.2 | Calculate Illustrative prepreg, 0.100 mm, εr 4.5 |
| JLCPCB JLC04161H-7628 drawing | 0.2104 | 4.4 | 0.3572 | 14.06 | 49.33 | 0.3498 | — | Calculate JLCPCB JLC04161H-7628 drawing |
| JLCPCB 7628, outer height 7.1 mil | 0.1803 | 4.4 | 0.3013 | 11.86 | 49.19 | 0.2936 | — | Calculate JLCPCB 7628, outer height 7.1 mil |
| JLCPCB JLC04161H-3313 | 0.0994 | 4.1 | 0.1629 | 6.41 | 47.44 | 0.1491 | T/H > 0.2 | Calculate JLCPCB JLC04161H-3313 |
| JLCPCB JLC04161H-2116 | 0.1164 | 4.16 | 0.193 | 7.60 | 47.98 | 0.1804 | T/H > 0.2 | Calculate JLCPCB JLC04161H-2116 |
| JLCPCB 6-layer 1.6 mm, outer 3313 | 0.0994 | 4.1 | 0.1629 | 6.41 | 47.44 | 0.1491 | T/H > 0.2 | Calculate JLCPCB 6-layer 1.6 mm, outer 3313 |
| PCBWay 4-layer 1.6 mm, 1 oz, 70% | 0.1855 | 4.74 | 0.2915 | 11.48 | 49.81 | 0.2897 | — | Calculate PCBWay 4-layer 1.6 mm, 1 oz, 70% |
| PCBWay 6-layer 1.6 mm, 1 oz, 70% | 0.1195 | 4.45 | 0.1873 | 7.37 | 48.60 | 0.1785 | T/H > 0.2 | Calculate PCBWay 6-layer 1.6 mm, 1 oz, 70% |
- Illustrative two-layer rows use H = 1.6 − 2 × 0.035 mm and the εr shown. They are not a vendor stackup.
- Illustrative prepreg rows are a single dielectric height at 1 oz. They are not a pressed glass style.
- JLCPCB drawing values are from the impedance stackup page: 7628 is 0.21040 mm at Dk 4.4, 3313 is 0.09940 mm at Dk 4.1, 2116 is 0.11640 mm at Dk 4.16, and the 1.6 mm six-layer outer ply shown there is 3313 at 0.09940 mm. Outer copper is 0.035 mm.
- An older JLCPCB impedance note said to use 7.1 mil as the dielectric height for an outer controlled-impedance track on 7628, which is 0.18034 mm. The current drawing lists 0.21040 mm. Both rows are computed.
- PCBWay rows use the laminated-structure page for 1.6 mm, finished outer copper 1 oz and 70% inner residual copper. The four-layer pressed 7628 is 0.1855 mm at Dk 4.74. The six-layer pressed 2116 is 0.1195 mm at Dk 4.45.
- T/H > 0.2 means the Hammerstad–Jensen thickness correction is outside the range this calculator flags. The width is still the solver’s 50 Ω root.
Common mistakes
- Using the finished board thickness as H. On four and six layers the outer reference is one prepreg away.
- Copying a 50 Ω width onto a different copper weight or a different εr. The sensitivity table is the size of that error.
- Trusting IPC-2141 above W/H = 2. The 3.3 mm Polar trace is the worked example: about 21 Ω from the formula and about 30 Ω from the field.
- Ignoring the solder mask, then treating a bare width as the coated width.
- Treating εr 4.2 and εr 4.5 as the same material. On 0.200 mm prepreg the 50 Ω widths are 0.3512 mm and 0.3314 mm.
- Quoting the quick width as a fabrication tolerance. The fabricator builds to their stackup and their process window.
Questions
What width is 50 Ω on 1.6 mm FR-4?
For an illustrative finished thickness of 1.6 mm with 1 oz on both sides, H = 1.530 mm. Hammerstad–Jensen gives 2.9642 mm at εr 4.2 and 2.8122 mm at εr 4.5. A real two-layer stackup may define 1.6 mm as the core instead. Use the dielectric height on the stackup sheet.
Why does IPC-2141 disagree with this calculator?
They are different fits. The quick result is Hammerstad–Jensen. IPC-2141 is shown beside it. Inside its usual range the two often differ by about an ohm at the Hammerstad–Jensen width. Outside W/H of 0.1 to 2, IPC-2141 can be far from a field solution, as the 3.3 mm Polar case shows.
How much does solder mask change a 50 Ω microstrip?
On the published JLCPCB mask and the JLC04161H-7628 bare 50 Ω width, the h/16 field solve moves from 50.98 Ω to 49.20 Ω, a drop of 1.79 Ω. Other heights and mask thicknesses move by a different amount. This model has no single ohms correction.
Which of these widths should I send to JLCPCB or PCBWay?
Send the target impedance and the layer, and use their current stackup. JLC04161H-7628’s drawing lists 0.2104 mm of 7628 at Dk 4.4, which this solver calls 0.3572 mm for bare 50 Ω. An older JLCPCB note said to use 7.1 mil, 0.1803 mm, as the outer-layer height for that ply, and that height calls for 0.3013 mm. The two published heights are not the same width.
Does a wider trace raise the impedance?
No. Increasing W lowers Z0. Increasing H raises Z0. Increasing εr or T lowers Z0. The sensitivity section is that statement with the model’s own numbers.
Can I use a microstrip width on an inner layer?
No. An inner trace between two planes is a stripline. On the published four-layer and six-layer drawings it is usually offset, so the symmetric formula does not apply. The differential-pair guide shows the centered formula, and the 2D solver covers an offset trace.
Sources
Independent project, without affiliation or endorsement by the cited authors, publishers or manufacturers. Trademarks belong to their respective owners.
- Qucs Technical Papers, microstrip equations 11.4–11.25
- Analog Devices MT-094, IPC-2141 surface microstrip
- Polar Instruments, Calculation of PCB Track Impedance
- Texas Instruments LVDS Owner’s Manual, edge-coupled factor
- JLCPCB controlled-impedance stackups
- JLCPCB impedance note, 7.1 mil outer height
- PCBWay multilayer laminated structure
PCB impedance guidesDifferential pair guideMethod and validation